UKM30-100S 100A 4P Molded Case Circuit Breaker 18 months warranty
thermal & electromagnetic 16,25,32,40,50,63,75,100A
Applications:
Circuit breakers UKM30 series (hereinafter referred to as-the
breaker) are for protection against overload and short circuit in
the circuit of 50HZ, reted voltage 660V, it also can be used for
non-frequent on-and-off switching operation ( uo to 30 times per
day) under normal circumstance.
The breakers are meets requirement of IEC / EN 60947-2.
Technical data:
| Parameter name | Value |
| UKM30-100S |
| Rated current In(A) | 16,25,32,40,50,63,75,100 |
| Number of poles | 4 |
| Rated voltage Ui(V) | AC690 |
| Arc distance (mm) | ≤50(0)* |
| Overcurrent release | Combined: thermal &electromagnetic |
| Rated ultimate breaking capitily Icu/Ics(KA) | AC690V | 5/3 |
| AC400V | 50/35 |
| AC230V | 100/50 |
| Operational performance (times) | ON | 6000 |
| OFF | 8500 |
| Dimensions (mm) | a | 120 |
| b | 155 |
| c | 68 |
*"0"arcing distance: please specify when ordering if you require.
The product shall be operated under the following environmental
conditions:
● Non-explosive;
● Does not contain corrosive gases and vapors in concentrations
destroying metals and insulation;
● Not rich conductive dust and vapors;
● Lack of direct exposure to ultraviolet radiation;
● Should not be signifinant shock or vibration.
Transport ans storage are only permitted in the original packing.
The ambient storage temperature:-45...+60° C and humidity not
above80% (at 25° C without condensation).
Installation and operating
The electrical work shall be performed by qualified personnel.
Before performing wiring work, turn off the upstream circuit
breaker and ensure that no curren is flowing through the breaker to
be wired.
Failure to do so may expose you to shock hazard.
When connecting any wire ,tighten the terminal screw to the torque
specified in this manual. Failure to do so may cause a fire.
Do not install the breaker in an abnormal environment. Protect the
circuit breaker so that the foreign particles,such as dust,concrete
or/and iron power, water and other moistures will not enter the
breaker. Failture to do so may make the breaker inoperative.
Connect the circuit breaker to power supply appropriate to the
rating voltage. Failure to do so may make the breaker inoperative
or damage it. The breaker is installed in a plastic or metal box on
a mounting plate with latches having two fixed positions. Power can
be supplied from both the upper and lower contacrts.Terminals allow
to connect copper or aluminum conductors.Before connecting standed
conductors, they must be tipped using an appropriate tool.
Safety requirements
Device maintenance and repair work may be carried out only by
appropriately authorized and trained personnel. Before any work
commences, the device must be disconnected from the supply.
Service
1. Delivery time: 20 working days for bulk order and depend on
ordering quantity
2. Strong production capacity and strict quality control system;
3. Your inquiry and problems related to our products or prices will
be replied in 24 hours;
4. Well-trained and experienced staffs to answer all your inquires;
5. After-sale tracking service for all of our clients;
6. OEM & ODM are available; there is an our own mould tooling
center in KRIPAL factory.
7. Payment: usually L/C, T/T,
8. Delivery way: Courier as door to door service (like DHL, TNT),
by sea, by air (airport to airport)
UKM30-100S 100A 4P Molded Case Circuit Breaker 18 months warranty
thermal & electromagnetic 16,25,32,40,50,63,75,100A
